EASTON UNI BUSHING CB ICS 12 GRAINS
EASTON UNI BUSHING CB ICS 12 GRAINS
RM36.00
Stock available
|
EASTON CARBON ONE PIN INSERT
EASTON CARBON ONE PIN INSERT
RM 43.00
|
|
|
|
|
|
|

The Beiter Insert-Nock has been designed to be inserted directly into Aluminum Shafts (instead of the cone or a Bushing!), but became very popular specially on Aluminum-Carbon Arrows.. The Beiter Insert-Nock is available in both the Beiter patented ASYMMETRIC shape, as well as in the SYMMETRIC Hunter-Nock. Remember to shoot with the Beiter logo on top!
Some features of Beiter Nocks, that distinguish them from other makes: Each Nock size has only one single mould. This offers highest precision and lowest tolerances. Every single Nock of one size comes out of the same mould. The Nock does not pinch on the nocking point, it rests there with a spring effect. The working life is much higher and, very important, the Beiter Nock guarantees constant release from the bowstring, shot after shot. The Beiter Insert-Nock is asymmetric, to adapt perfectly to the asymmetric drawn string. To ensure the Nock is placed correctly, see that the notch for the nocking point, looks to the front. The Beiter Insert-Nock can be shot without problem with all known nocking points; but the Beiter nocking point is the ideal partner for it. If used together, they avoid the arrow nocking out of the string at full draw and have ideal gliding surfaces.
The Beiter Insert-Nock has been designed to be inserted directly into Aluminum Shafts (instead of the cone or a Bushing!), but became very popular specially on Aluminum-Carbon Arrows.. The Beiter Insert-Nock is available in both the Beiter patented ASYMMETRIC shape, as well as in the SYMMETRIC Hunter-Nock. Remember to shoot with the Beiter logo on top!
Some features of Beiter Nocks, that distinguish them from other makes: Each Nock size has only one single mould. This offers highest precision and lowest tolerances. Every single Nock of one size comes out of the same mould. The Nock does not pinch on the nocking point, it rests there with a spring effect. The working life is much higher and, very important, the Beiter Nock guarantees constant release from the bowstring, shot after shot. The Beiter Insert-Nock is asymmetric, to adapt perfectly to the asymmetric drawn string. To ensure the Nock is placed correctly, see that the notch for the nocking point, looks to the front. The Beiter Insert-Nock can be shot without problem with all known nocking points; but the Beiter nocking point is the ideal partner for it. If used together, they avoid the arrow nocking out of the string at full draw and have ideal gliding surfaces.
RM 60.00
|
|
ACCURA XG NOCK (20 PIECES)
• Precision-molded, press fit
• Fits 4MM UNI bushings or arrow shafts with .166" ID
• Available in two throat sizes
• .088" small groove
• .098" large groove
• Sold in dozen packs
Suitable for arrow :
- ACCURA X ONE PRIME CARBON
- ACCURA X PLUS
- EASTON CARBON ONE
- EASTON APOLLO
- EASTON ACG ALUMINIUM
ACCURA XG NOCK (20 PIECES)
• Precision-molded, press fit
• Fits 4MM UNI bushings or arrow shafts with .166" ID
• Available in two throat sizes
• .088" small groove
• .098" large groove
• Sold in dozen packs
Suitable for arrow :
- ACCURA X ONE PRIME CARBON
- ACCURA X PLUS
- EASTON CARBON ONE
- EASTON APOLLO
- EASTON ACG ALUMINIUM
RM 21.00
|

The Beiter Insert-Nock has been designed to be inserted directly into Aluminum Shafts (instead of the cone or a Bushing!), but became very popular specially on Aluminum-Carbon Arrows..
The Beiter Insert-Nock is available in both the Beiter patented ASYMMETRIC shape, as well as in the SYMMETRIC Hunter-Nock. Remember to shoot with the Beiter logo on top!
Some features of Beiter Nocks, that distinguish them from other makes:
Each Nock size has only one single mould. This offers highest precision and lowest tolerances. Every single Nock of one size comes out of the same mould.
The Nock does not pinch on the nocking point, it rests there with a spring effect. The working life is much higher and, very important, the Beiter Nock guarantees constant release from the bowstring, shot after shot.
The Beiter Insert-Nock is asymmetric, to adapt perfectly to the asymmetric drawn string. To ensure the Nock is placed correctly, see that the notch for the nocking point, looks to the front.
The Beiter Insert-Nock can be shot without problem with all known nocking points; but the Beiter nocking point is the ideal partner for it. If used together, they avoid the arrow nocking out of the string at full draw and have ideal gliding surfaces.
Note:
- arrow fitting for ID arrow 0.166" or 4.2mm
- suitable for any arrow fitting with Easton G nock 4 mm
- some arrow maybe a bit tight and some might need to use white tape to tighten it (as Beiter Outnock)
- recommended for EASTON arrows
The Beiter Insert-Nock has been designed to be inserted directly into Aluminum Shafts (instead of the cone or a Bushing!), but became very popular specially on Aluminum-Carbon Arrows..
The Beiter Insert-Nock is available in both the Beiter patented ASYMMETRIC shape, as well as in the SYMMETRIC Hunter-Nock. Remember to shoot with the Beiter logo on top!
Some features of Beiter Nocks, that distinguish them from other makes:
Each Nock size has only one single mould. This offers highest precision and lowest tolerances. Every single Nock of one size comes out of the same mould.
The Nock does not pinch on the nocking point, it rests there with a spring effect. The working life is much higher and, very important, the Beiter Nock guarantees constant release from the bowstring, shot after shot.
The Beiter Insert-Nock is asymmetric, to adapt perfectly to the asymmetric drawn string. To ensure the Nock is placed correctly, see that the notch for the nocking point, looks to the front.
The Beiter Insert-Nock can be shot without problem with all known nocking points; but the Beiter nocking point is the ideal partner for it. If used together, they avoid the arrow nocking out of the string at full draw and have ideal gliding surfaces.
Note:
- arrow fitting for ID arrow 0.166" or 4.2mm
- suitable for any arrow fitting with Easton G nock 4 mm
- some arrow maybe a bit tight and some might need to use white tape to tighten it (as Beiter Outnock)
- recommended for EASTON arrows
RM 140.00
|
The Beiter Out-Nock has been mainly designed for Carbon Arrowshafts, but can be used on some Aluminum-Carbon Arrows as well. The Beiter Out-Nock is available exclusively in the Beiter patented ASYMMETRIC shape.
Remember to shoot with the Beiter logo on top!
Some features of Beiter Nocks, that distinguish them from other makes:
-Each Nock size has only one single mould. This offers highest precision and lowest tolerances. Every single Nock of one size comes out of the same mould!
-The Nock does not pinch on the Nocking Point, it rests there with a spring effect. The working life is much higher and, very important, the Beiter Nock guarantees constant release from the bowstring, shot after shot.
-The Beiter Nock is asymmetric, to adapt perfectly to the asymmetric drawn string. To ensure the Nock is placed correctly, see that the notch for the nocking point, is to the front.
-The Beiter Nock can be shot without problem with all known nocking points; but the Beiter nocking point is the ideal partner for it. If used together, they avoid the arrow nocking out of the string at full draw and have ideal gliding surfaces.
SIZE :
#1 / (SMALL GROOVE)
#2 / (LARGE GROOVE)
The Beiter Out-Nock has been mainly designed for Carbon Arrowshafts, but can be used on some Aluminum-Carbon Arrows as well. The Beiter Out-Nock is available exclusively in the Beiter patented ASYMMETRIC shape.
Remember to shoot with the Beiter logo on top!
Some features of Beiter Nocks, that distinguish them from other makes:
-Each Nock size has only one single mould. This offers highest precision and lowest tolerances. Every single Nock of one size comes out of the same mould!
-The Nock does not pinch on the Nocking Point, it rests there with a spring effect. The working life is much higher and, very important, the Beiter Nock guarantees constant release from the bowstring, shot after shot.
-The Beiter Nock is asymmetric, to adapt perfectly to the asymmetric drawn string. To ensure the Nock is placed correctly, see that the notch for the nocking point, is to the front.
-The Beiter Nock can be shot without problem with all known nocking points; but the Beiter nocking point is the ideal partner for it. If used together, they avoid the arrow nocking out of the string at full draw and have ideal gliding surfaces.
SIZE :
#1 / (SMALL GROOVE)
#2 / (LARGE GROOVE)
RM 120.00
|
|
|

EASTON NOCK COLLAR - 1 DOZ - (12 PCS)
Protects the rear of your shaft from impacts and cracking
Protects the rear of your shaft from impacts and cracking
Compatible with Easton Ace, ProComp, Avance, Avance Sport, SuperDrive Micro, 4mm FMJ, 4mm Axis, and AC ProComp
Weight: 3 grain
Sold in a pack of 12
Target Fitment:
#1 Fits all ACE spine sizes | ProComp spine size 1150-880 | Avance spine size 2000-1400
#2 Fits ProComp spine size 810-660 | Avance spine size 1150-810 | SuperDrive Micro spine size 950-625
#3 Fits ProComp spine size 520-470 | Avance spine size 730-660 | SuperDrive Micro spine size 575-475
#4 Fits ProComp spine size 420-340 | Avance spine size 600-450 | SuperDrive Micro spine size 425-375
#5 Fits ProComp spine size 300 | Avance spine size 400 | SuperDrive Micro spine size 325
#7 Fits ProComp spine size 250 | Avance spine size 340
Protects the rear of your shaft from impacts and cracking
Compatible with Easton X10 and X10 ProTour
Weight: 3 grain
Sold in a pack of 12
Fitment:
#1 Fits all X10 spine sizes
#2 Fits 770-670 spine X10 Pro Tours
#3 Fits 620-520 spine X10 Pro Tours
#4 Fits 470-420 spine X10 Pro Tours
#5 Fits 380-340 spine X10 Pro Tours
EASTON NOCK COLLAR - 1 DOZ - (12 PCS)
Protects the rear of your shaft from impacts and cracking
Protects the rear of your shaft from impacts and cracking
Compatible with Easton Ace, ProComp, Avance, Avance Sport, SuperDrive Micro, 4mm FMJ, 4mm Axis, and AC ProComp
Weight: 3 grain
Sold in a pack of 12
Target Fitment:
#1 Fits all ACE spine sizes | ProComp spine size 1150-880 | Avance spine size 2000-1400
#2 Fits ProComp spine size 810-660 | Avance spine size 1150-810 | SuperDrive Micro spine size 950-625
#3 Fits ProComp spine size 520-470 | Avance spine size 730-660 | SuperDrive Micro spine size 575-475
#4 Fits ProComp spine size 420-340 | Avance spine size 600-450 | SuperDrive Micro spine size 425-375
#5 Fits ProComp spine size 300 | Avance spine size 400 | SuperDrive Micro spine size 325
#7 Fits ProComp spine size 250 | Avance spine size 340
Protects the rear of your shaft from impacts and cracking
Compatible with Easton X10 and X10 ProTour
Weight: 3 grain
Sold in a pack of 12
Fitment:
#1 Fits all X10 spine sizes
#2 Fits 770-670 spine X10 Pro Tours
#3 Fits 620-520 spine X10 Pro Tours
#4 Fits 470-420 spine X10 Pro Tours
#5 Fits 380-340 spine X10 Pro Tours
RM 80.00
|
|
|
ACCURA X PIN INSERT (1 DOZEN)
ACCURA X PIN INSERT (1 DOZEN)
RM 29.00
|
ACCURA X PIN NOCK (20 PIECES)
ACCURA X PIN NOCK (20 PIECES)
RM 38.00
|
|
|
BEITER PIN NOCK (1 DOZEN)
BEITER PIN NOCK (1 DOZEN)
RM 69.00
|
|
|
|
EASTON G NOCK ( 1 DOZEN )
EASTON G NOCK ( 1 DOZEN )
RM 39.00
|
EASTON G PIN NOCKS LARGE GROOVE( 1 DOZEN )
EASTON G PIN NOCKS LARGE GROOVE( 1 DOZEN )
RM 65.00
|
EASTON PIN NOCK (1 DOZEN)
EASTON PIN NOCK (1 DOZEN)
RM 63.00
|
EASTON SUPER NOCK ( 1 DOZEN )
EASTON SUPER NOCK ( 1 DOZEN )
RM 22.00
|